general purpose relays power relays t9a series, dc coil 30a pcb or panel mount relay 08-2012, rev. 0812 www.te.com ? 2012 tyco electronics corporation, a te connectivity ltd. company datasheets and product specifcation according to iec 61810-1 and to be used only together with the defnitions section. datasheets and product data is subject to the terms of the disclaimer and all chapters of the defnitions section, available at http://relays.te.com/definitions datasheets, product data, defnitions sec - tion, application notes and all specifcations are subject to change. 1 potter & brumfeld contact ratings 1) (continued) type load cycles ul 508/873 agsnoino, 1w coil no 30a, 240vac, general purpose 100x10 3 no 80lra/30fla, 240vac 30x10 3 nc 10a, 250vac, resistive 50x10 3 agcdo, 900mw coil no 30a, 240vac, general purpose 100x10 3 no 18a, 240vac, resistive, 105c 100x10 3 nc 15a, 240vac, resistive 6x10 3 no 30lra/15fla, 240vac 100x10 3 no 50lra/16fla, 120vac 100x10 3 no 30lra/11fla, 120vac 200x10 3 1) contact ratings at 25c (unless otherwise noteed) with relay properly vented. remove vent nib after soldering and cleaning. mechanical endurance 10x10 6 ops. coil data coil voltage range 5 to 110vdc max. coil power 110% of nominal max. coil temperature 155c coil insulation system according ul class f coil versions, dc coil coil rated operate release coil rated coil code voltage voltage voltage resistance power vdc vdc vdc ?10% w code d (1w) coil 5 5 3.75 0.5 25 1 6 6 4.5 0.6 36 1 9 9 6.75 0.9 81 1 12 12 9 1.2 144 1 15 15 11.25 1.5 225 1 18 18 13.5 1.8 324 1 24 24 18 2.4 576 1 48 48 36 4.8 2304 1 110 110 82.5 11 12100 1 code l (900w) coil 5 5 3.75 0.5 27 .9 6 6 4.5 0.6 40 .9 9 9 6.75 0.9 97 .9 12 12 9 1.2 155 .9 15 15 11.25 1.5 256 .9 18 18 13.5 1.8 380 .9 24 24 18 2.4 660 .9 48 48 36 4.8 2560 .9 110 110 82.5 11 13450 .9 all fgures are given for coil without preenergization, at ambient temperature +23c. n 30a switching in 1 form a (no) and 20a in 1 form c (co) n plastic sealed case available n meets ul 508 and 873 spacing - 3.18mm through air, 6.36mm over surface n option for load connections via 0.250 (6.35mm) q.c. terminals n ul class f insulation system standard typical applications hvac, appliances, industrial controls approvals ul e58304; csa lr48471 technical data of approved types on request contact data contact arrangement 1 form a (no), 1 form b (nc), 1 form c (co) rated voltage 277vac max. switching voltage 277vac rated current 30a 15a 20a/10a limiting continuous current 30a contact material agsnoino, agcdo min. recommended contact load 1a, 5vdc or 12vac initial contact resistance 75 m? at 1a at 5vdc or 12vac frequency of operation, with/without load 360/3600hr operate/release time max., including bounce 15/15ms contact ratings 1) type load cycles factory agcdo, 1w coil no 30a, 240vac, general purpose 100x10 3 no 25a, 240vac, resistive 100x10 3 co 20a/10a, 240vac, general purpose 100x10 3 co 20a/10a, 240vac, resistive 100x10 3 co 20a/10a, 28vdc, resistive 100x10 3 ul 508/873 agcdo, 1w coil no 30a, 240vac, general purpose 100x10 3 nc 15a, 240vac, general purpose 100x10 3 co 20a/10a, 240vac, general purpose 100x10 3 no 25a, 240vac, resistive 6x10 3 nc 20a, 240vac, resistive 6x10 3 co 16.75a/13.4a, 240vac, resistive 6x10 3 no 80lra/30fla, 240vac 30x10 3 nc 30lra/12fla, 240vac 30x10 3 co 53.6lra/20fla / 20lra/8fla, 240vac 30x10 3 no 98lra/22fla, 120vac 100x10 3 no 2hp, 240vac 1x10 3 nc 1/2hp, 240vac 1x10 3 no 1hp, 125vac 1x10 3 nc 1/4hp, 125vac 1x10 3 no 10a, 277vac, ballast 6x10 3 nc 3a, 277vac, ballast 6x10 3 no 8.3a, 120vac, tungsten 6x10 3 no 5.4a, 277vac, tungsten 6x10 3 no 470va, 120vac, pilot duty 30x10 3 no 20a, 28vdc, resistive 100x10 3 nc 10a, 28vdc, resistive 100x10 3 agcdo - enhanced version only, 1w coil no 21a, 250vac, resistive 250x10 3 no 25a, 277vac, resistive 100x10 3 1) contact ratings at 25c (unless otherwise noted) with relay properly vented. remove vent nib after soldering and cleaning.
general purpose relays power relays t9a series, dc coil 30a pcb or panel mount relay (continued) 08-2012, rev. 0812 www.te.com ? 2012 tyco electronics corporation, a te connectivity ltd. company datasheets and product specifcation according to iec 61810-1 and to be used only together with the defnitions section. datasheets and product data is subject to the terms of the disclaimer and all chapters of the defnitions section, available at http://relays.te.com/definitions datasheets, product data, defnitions sec - tion, application notes and all specifcations are subject to change. 2 potter & brumfeld insulation data initial dielectric strength between open contacts 1500v rms between contact and coil 2500v rms initial surge withstand voltage between contact and coil 6kv initial insulation resistance between insulated elements 1x10 9 ? clearance/creepage between contact and coil 3.18mm clearance/6.3638mm other data material compliance: eu rohs/elv, china rohs, reach, halogen content refer to the product compliance support center at www.te.com/customersupport/rohssupportcenter ambient temperature dc coil -55oc to 85oc 3) 105c models available category of environmental protection iec 61810 rt0 - open, rti - dust protected, rtii - fux proof, rtiii - wash tight vibration resistance (functional) 1.65mm max excursions, 10-55 hz shock resistance (functional) 10g for 11msec shock resistance (destructive) 100g terminal type pcb-tht and pcb-tht + quick connect weight 26g mounting code 1 33g mounting codes 2 and 5 resistance to soldering heat tht iec 60068-2-20 250c packaging/unit tray/50 pcs., bundle/250 pcs., box/500 pcs. 3) operating ambient temperature must consider must operate voltage change over temperature, contact temperature rise, coil temperature rise (if coil is not allowed to cool) and maximum coil temperature. specifcation ambient considers 20a load with coil cooled to ambient. coil data (continued) ambient temperature vs. coil voltage C 1w coil data below are average values and should be verifed in application. tests were conducted within a 2 (.6 m) cube (still air); at nominal coil power @ 25c; with normally open contact loaded; and with 4 (1.22 m) long, #10 awg load wires. p.c. board relays were mounted to a 30a, single side p.c. board. coil rise test conducted with a 30a pc board to maintain 20c max. rize at 30c. the relay connections and wiring must be designed with an adequate cross section to ensure proper current fow and heat dissipation. 2) remove knock-off nib after cleaning process for optimum life of wash-tight relays. 0 20 40 60 80 100 120 140 180 160 140 120 100 80 60 wash-tight relay, vented (2 , load connections via q.c. terminals, pc mount 0a 10a 20a 30a applied coil voltage (% of rated voltage) max. alowable ambient temp. (c) 40 60 80 100 120 140 180 160 140 120 100 80 60 dust protected relay, flange mount 0a 10a 20a 30a applied coil voltage (% of rated voltage) max. alowable ambient temp. (c) 0 20 40 60 80 100 120 140 180 160 140 120 100 80 60 0a 10a 20a 30a wash-tight relay, vented (2 pc terminals for coil & contacts applied coil voltage (% of rated voltage) max. alowable ambient temp. (c) dimensions t9as C mounting and termination code 2 t9ap C mounting and termination code 5 .032 x .062 (.81 x 1.57) .045 x .045 (1.14 x 1.14) .03 (.80) 2 places .250 x .032 quick (6.35 x .81) connect nc no com 1.280 max. (32.51) 1.080 max. (27.43) .130 .020 (3.30 .51) 1.100 max. (27.94) ? .187 x .020 (4.75 x .508) quick connect 1.080 max. (27.43) 1.980 max. (50.29) 1.713 .010 (43.51 .25) .071 (1.80) rad. for #6 screw 1.280 max. (32.51) 1.100 max. (27.94) .250 x .032 (6.35 x .81) quick connect nc no com note: recommended mounting screw torque is 4.0-5.0 lbs.in when #6 screw is used.
general purpose relays power relays t9a series, dc coil 30a pcb or panel mount relay (continued) 08-2012, rev. 0812 www.te.com ? 2012 tyco electronics corporation, a te connectivity ltd. company datasheets and product specifcation according to iec 61810-1 and to be used only together with the defnitions section. datasheets and product data is subject to the terms of the disclaimer and all chapters of the defnitions section, available at http://relays.te.com/definitions datasheets, product data, defnitions sec - tion, application notes and all specifcations are subject to change. 3 potter & brumfeld terminal assignment bottom view on pins 1 form a 1 form b 1 form c product code structure typical product code t9a s 5 d 2 2 -12 type t9a power pcb or panel mount relay t9a enclosure n open, no enclosure (requires mounting code 1) p dust protected plastic case (requires mounting code 5) s wash-tight plastic case with knock off nib (requires mounting code 1 or 2) v flux-proof plastic case (requires mounting code 1 or 2) contact arrangement 1 1 form a (1 no) 2 1 form b (1 nc) 5 1 form c (1 co) coil input d dc voltage, 1w l dc voltage, 900mw mounting and termination 1 pcb mounting; pcb terminals for coil and contacts (only available with enclosure code n, s or v) 2 pcb mounting; pcb term. for coil and contacts; 6.35mm (.250in) qc for contacts (only available with enclosure code s or v) 5 flanged mounting; 4.75mm (.187) qc for coil; 6.35mm (.250in) qc for contacts (only available with enclosure code p) contact material 2 agcdo 4 agsnoino 7 agcdo (enhanced version) coil voltage coil code: please refer to coil versions table dimensions plain case bracket mount case .032 x .062 (.8 x 1.6) terminals .212 max. (5.38) .10 max. (2.54) .045 x .045 (1.14 x 1.14) terminal .805 max. (20.4) .69 (17.6) 1 .280 max. (32.51) 1.08 max. (27.43) .50 (12.8) .03 (.80) terminals .130 + .016 C .010 3.30 + .41 C.25 ( ) ? .016 (.43) .950 max. (24.13) 1.20 max. (30.5) .680 max. (17.27) .130 .020 (3.3 .51) .045 x .045 (1.14 x 1.14) terminal .032 x .062 (.8 x 1.6) terminals .03 (0.80) terminals ? pcb layout bottom view on pins t9ap/s - mounting and termination code 2 t9as/v - mounting and termination code 1 .140 max. (3.56) .250 max. (6.35) .300 (7.62) .100 (2.54) .150 (3.81) .500 (12.7) .550 (13.97) .700 (17.78) .043 .003 dia. (1.09 .08) .081 .005 dia. (2.06 .13) .600 (15.24) .078 .003 dia. (1.98 .08) .300 (7.62) .100 (2.54) .150 (3.81) .500 (12.7) .550 (13.97) .700 (17.78) .043 .003 dia. (1.09 .08) .081 .005 dia. (2.06 .13) .600 (15.24) .212 max. (5.38) .078 .003 dia. (1.98 .08) only necessary terminals are present on single throw models. consequently, some holes will be unnecessary for single throw models. only necessary terminals are present on single throw models. consequently, some holes will be unnecessary for single throw models.
general purpose relays power relays t9a series, dc coil 30a pcb or panel mount relay (continued) 08-2012, rev. 0812 www.te.com ? 2012 tyco electronics corporation, a te connectivity ltd. company datasheets and product specifcation according to iec 61810-1 and to be used only together with the defnitions section. datasheets and product data is subject to the terms of the disclaimer and all chapters of the defnitions section, available at http://relays.te.com/definitions datasheets, product data, defnitions sec - tion, application notes and all specifcations are subject to change. 4 potter & brumfeld product code enclosure contacts coil mounting contact material coil part number ?t9an1l22-24 open (no cover) 1 form a, 1 no 900mw pcb + qc agcdo 24vdc 1419104-6? ?t9an5l12-24 1 form c, 1 co pcb terminals 1-1393210-0? ?t9an5l22-24 pcb + qc 1419104-9? ?t9ap1d52-12 unsealed, plastic dust cover 1 form a, 1 no 1w flanged mount, qc 12vdc 6-1419102-0? ?t9ap1d52-24 24vdc 6-1419102-3? ?t9ap1d52-48 48vdc 5-1419102-8? ?t9ap1d54-24 agsnoino 24vdc 7-1423091-3? ?t9ap5d52-12 1 form c, 1 co agcdo 12vdc 5-1419102-4? ?t9ap5d52-24 24vdc 5-1419102-2? ?t9ap5d52-48 48vdc 6-1419102-4? ?t9ap5d54-12 agsnoino 12vdc 7-1423091-4? ?t9ap5d54-24 24vdc 7-1423091-5? ?t9as1d12-5 wash tight, knock off nib 1 form a, 1 no pcb terminals agcdo 5vdc 2-1393210-0? ?t9as1d12-9 9vdc 2-1393210-2? ?t9as1d12-12 12vdc 1-1393210-3? ?t9as1d12-15 15vdc 1-1393210-4? ?t9as1d12-18 18vdc 1-1393210-5? ?t9as1d12-24 24vdc 1-1393210-8? ?t9as1d12-48 48vdc 1-1393210-9? ?t9as1d12-110 110vdc 1-1393210-2? ?t9as1d14-12 agsnoino 12vdc 5-1423091-7? ?t9as1d14-24 24vdc 6-1423091-3? ?t9as1d17-12 agcdo enhanced 12vdc 1423029-5? ?t9as1d17-24 24vdc 1423029-6? ?t9as1d22-5 pcb + qc agcdo 5vdc 2-1419104-3? ?t9as1d22-12 12vdc 1-1419104-7? ?t9as1d22-24 24vdc 2-1419104-1? ?t9as1d22-48 48vdc 2-1419104-2? ?t9as1d22-110 110vdc 1-1419104-6? ?t9as1d27-12 agcdo enhanced 12vdc 2071229-4? ?t9as1d27-24 24vdc 2071229-4? ?t9as1l12-12 900mw pcb terminals agcdo 12vdc 2-1393210-4? ?t9as1l12-24 24vdc 2-1393210-5? ?t9as1l22-18 pcb + qc 18vdc 2-1419104-6? ?t9as2l22-24 1 form b, 1 nc 24vdc 1423794-1? ?t9as5d12-5 1 form c, 1 co 1w pcb terminals 5vdc 3-1393210-9? ?t9as5d12-12 12vdc 3-1393210-3? ?t9as5d12-18 18vdc 3-1393210-4? ?t9as5d12-24 24vdc 3-1393210-7? ?t9as5d12-48 48vdc 3-1393210-8? ?t9as5d12-110 110vdc 3-1393210-2? ?t9as5d14-5 agsnoino 5vdc 6-1423091-4? ?t9as5d22-5 pcb + qc agcdo 3-1419104-9? ?t9as5d22-12 12vdc 3-1419104-3? ?t9as5d22-24 24vdc 3-1419104-6? ?t9as5d22-110 110vdc 3-1419104-2? ?t9as5d24-5 agsnoino 5vdc 6-1423091-9? ?t9as5d24-12 12vdc 7-1423091-0? ?t9as5d24-24 24vdc 7-1423091-1? ?t9as5l12-12 900mw pcb terminals agcdo 12vdc 4-1393210-1? ?t9as5l22-18 pcb + qc 18vdc 4-1419104-0? ?t9as5l22-24 24vdc 4-1419104-1? ?t9as5l22-48 48vdc 9-1419136-6? ?t9av1d12-12 vented, fux tight 1 form a, 1 no 1w pcb terminals 12vdc 4-1393210-3? ?t9av1d12-18 18vdc 5-1393210-2? ?t9av1d22-18 pcb + qc 4-1419148-8? ?t9av1d22-24 24vdc 5-1419148-0? ?t9av1d22-48 48vdc 2-1423091-3? ?t9av1l12-12 900mw pcb terminals 12vdc 1-1423091-8? ?t9av1l22-24 pcb + qc 24vdc 4-1419104-2? ?t9av2d22-24 1 form b, 1nc 1w 1419137-1? ?t9av5d12-24 1 form c, 1co pcb terminals 4-1393210-8? ?t9av5d22-18 pcb + qc 18vdc 5-1419148-2? ?t9av5d22-24 24vdc 1419137-2? ?t9av5l12-12 900mw pcb terminals 12vdc 1423091-6?
|
